「Debian/HDDのフォーマット」の編集履歴（バックアップ）一覧はこちら

「Debian/HDDのフォーマット」(2009/08/16 (日) 23:20:08) の最新版変更点

追加された行は緑色になります。

削除された行は赤色になります。

RIGHT:&lastmod;
*目次 [#rf4d19ae]
#contents
*パーティションを作成 [#ab98cfc1]
**パーティションを作成 [#l86e0c65]
 # fdisk
 Usage: fdisk [-l] [-b SSZ] [-u] device
 E.g.: fdisk /dev/hda  (for the first IDE disk)
   or: fdisk /dev/sdc  (for the third SCSI disk)
   or: fdisk /dev/eda  (for the first PS/2 ESDI drive)
   or: fdisk /dev/rd/c0d0  or: fdisk /dev/ida/c0d0  (for RAID devices)
   ...
 
 # fdisk /dev/sdb
 Device contains neither a valid DOS partition table, nor Sun, SGI or OSF disklabel
 Building a new DOS disklabel. Changes will remain in memory only,
 until you decide to write them. After that, of course, the previous
 content won't be recoverable.
 
 
 The number of cylinders for this disk is set to 38913.
 There is nothing wrong with that, but this is larger than 1024,
 and could in certain setups cause problems with:
 1) software that runs at boot time (e.g., old versions of LILO)
 2) booting and partitioning software from other OSs
    (e.g., DOS FDISK, OS/2 FDISK)
 Warning: invalid flag 0x0000 of partition table 4 will be corrected by w(rite)
 
 Command (m for help): p
 
 Disk /dev/sdb: 320.0 GB, 320072933376 bytes
 255 heads, 63 sectors/track, 38913 cylinders
 Units = cylinders of 16065 * 512 = 8225280 bytes
 
    Device Boot      Start         End      Blocks   Id  System
 
 Command (m for help): n
 Command action
    e   extended
    p   primary partition (1-4)
 p
 Partition number (1-4): 1
 First cylinder (1-38913, default 1):
 Using default value 1
 Last cylinder or +size or +sizeM or +sizeK (1-38913, default 38913):
 Using default value 38913
 
 Command (m for help): w
 The partition table has been altered!
 
 Calling ioctl() to re-read partition table.
 Syncing disks.

**パーティションが作成された事を確認する [#r7e05be9]
 # fdisk /dev/sdb
 The number of cylinders for this disk is set to 38913.
 There is nothing wrong with that, but this is larger than 1024,
 and could in certain setups cause problems with:
 1) software that runs at boot time (e.g., old versions of LILO)
 2) booting and partitioning software from other OSs
    (e.g., DOS FDISK, OS/2 FDISK)
 
 Command (m for help): p
 
 Disk /dev/sdb: 320.0 GB, 320072933376 bytes
 255 heads, 63 sectors/track, 38913 cylinders
 Units = cylinders of 16065 * 512 = 8225280 bytes
 
    Device Boot      Start         End      Blocks   Id  System
 /dev/sdb1               1       38913   312568641   83  Linux
 
 Command (m for help): q

*ファイルシステムの作成 [#n6c2855c]
Ext3なら
 # mkfs.ext3 /dev/sdb1
Fat32なら
 # mkdosfs -F 32 /dev/sdb1